[DXLog.net - Support] Version 2.0

[9A5K]

FB Ulf.

Yes, default CW messages are stored in config files.
If use change some of them, it is saved in currently opened log file (.dxn).

Also, if you're in the network (for multi op), you can synchronize all
messages on all stations by simple click in menu on
Options->Networking->Synchronize CW messages.

Also, default CW messages can be defined in config file based on some
conditions (based on EXCHANGE box in config screen).
One of the examples of such practice is WAG contest, where DL stations
should send RST + DOK, and all other stations
sending RST + SERIAL NUMBER..

In v2.0.10 it is configured for all stations the same, but with v2.0.11
there will be changed WAG.txt config file with following lines:

# CW Messages
# Default for DL Stations
CW_Message_1 = CQ $MYCALL $MYCALL ++TEST--
CW_Message_2 = ++$RST-- $EXCHANGE
CW_Message_3 = $EXCHANGE
CW_Message_4 = $MYCALL
CW_Message_5 = $LOGGEDCALL
CW_Message_6 = NR?
CW_Message_7 = ?
CW_Message_INS = $LOGGEDCALL $QSOB4 $F2
CW_Message_PLUS = $CORRECT ++TU-- $CR $MYCALL

# CW Messages for NON DL stations (if config exchange field = DX)
CW_MESSAGE_EXCHANGE_FILTER=^DX$
CW_Message_1 = CQ $MYCALL $MYCALL ++TEST--
CW_Message_2 = ++$RST-- $SERIAL
CW_Message_3 = $SERIAL
CW_Message_4 = $MYCALL
CW_Message_5 = $LOGGEDCALL
CW_Message_6 = NR?
CW_Message_7 = ?
CW_Message_INS = $LOGGEDCALL $QSOB4 $F2
CW_Message_PLUS = $CORRECT ++TU-- $CR $MYCALL


So, default messages are defined first.
And afterwards comes filtered message (in example above if EXCHANGE field
is field with DX, bottom set of messages will be used)..

73,
Chris - 9A5K




On Wed, Sep 11, 2013 at 7:30 AM, Ulf Schneider <uschneid at posteo.de> wrote:

> Hi Chris,
>
> thanks for the information. That was a good hint to have a look at the
> contest configuration files. I just learned that each contest has
> configurable CW messages. Nice!
>
> 73
> Ulf DK5TX
>
>
> Am 10.09.2013 21:19 schrieb 9A5K:
>
>> Good eye Ulf..
>>
>> Actually, Check mults window was showing only data from MULT1 calculation.
>> Now changed to show all three possible Mults...
>> In WAE, DXLog.net using two MULT variables for calculation.
>>
>> It's defined like this in config file.
>>
>> MULT1_TYPE=DXCC
>> MULT1_COUNT=PER_BAND
>> MULT1_FIELD=FROM_DXCC
>> MULT1_DISPLAY=MULT
>> MULT1_BAND_BONUS=80;4
>> MULT1_BAND_BONUS=40;3
>> MULT1_BAND_BONUS=20;2
>> MULT1_BAND_BONUS=15;2
>> MULT1_BAND_BONUS=10;2
>>
>> MULT1_EXCEPTION=DEST->DXCC:^K$**|^VE$|^VK$|^ZL$|^ZS$|^JA$|^PY$**
>> |^UA9$;NONE
>>
>> MULT2_TYPE=PFX_AREA
>> MULT2_COUNT=PER_BAND
>> MULT2_FIELD=FROM_DXCC
>> MULT2_DISPLAY=MULT
>> MULT2_BAND_BONUS=80;4
>> MULT2_BAND_BONUS=40;3
>> MULT2_BAND_BONUS=20;2
>> MULT2_BAND_BONUS=15;2
>> MULT2_BAND_BONUS=10;2
>>
>> MULT2_EXCEPTION=DEST->DXCC:^K$**|^VE$|^VK$|^ZL$|^ZS$|^JA$|^PY$**
>> |^UA9$;PFX_AREA
>> MULT2_EXCEPTION=ALL;NONE
>>
>> This means that MULT1 is calculated from DXCC. The exceptions are K, VE,
>> VK, ZL, ZS, JA, PY and UA9 DXCC where we
>> are taking country prefix area, which is calculated as mult 2...
>>
>> Fixed now.
>>
>> Thanks.
>>
>> 73,
>> Chris - 9A5K
>>
>>
>>
>> On Tue, Sep 10, 2013 at 9:03 PM, Ulf Schneider <uschneid at posteo.de>
>> wrote:
>>
>>  Hi Chris,
>>>
>>> still playing around ... I just noticed a strange behaviour of the check
>>> multipliers window. It shows me only if I worked already a specific
>>> callsign, but not a specific country/multiplier
>>>
>>> See here:
>>>
>>> http://5tx.de/dev/null/****CheckMultipliers1.jpg<http://5tx.de/dev/null/**CheckMultipliers1.jpg>
>>> <http://**5tx.de/dev/null/**CheckMultipliers1.jpg<http://5tx.de/dev/null/CheckMultipliers1.jpg>
>>> >
>>>
>>> KC1XX is shown in the check multipliers window as worked multi on 20m.
>>>
>>>
>>> http://5tx.de/dev/null/****CheckMultipliers2.jpg<http://5tx.de/dev/null/**CheckMultipliers2.jpg>
>>> <http://**5tx.de/dev/null/**CheckMultipliers2.jpg<http://5tx.de/dev/null/CheckMultipliers2.jpg>
>>> >
>>>
>>> If some other callsign from W1 is in the callsign field, the check
>>> multipliers window doesn't show the worked multi on 20m.
>>>
>>> Tnx for fixing the repeat loop bug.
>>>
>>>
>>> 73
>>> Ulf DK5TX
>>>
>>> ______________________________****_________________
>>> Support mailing list
>>> Support at dxlog.net
>>>
>>> http://www.dxlog.net/mailman/****listinfo/support<http://www.dxlog.net/mailman/**listinfo/support>
>>> <http://www.**dxlog.net/mailman/listinfo/**support<http://www.dxlog.net/mailman/listinfo/support>
>>> >
>>>
>>>  ______________________________**_________________
> Support mailing list
> Support at dxlog.net
> http://www.dxlog.net/mailman/**listinfo/support<http://www.dxlog.net/mailman/listinfo/support>
>