[DXLog.net - Support] DXLog MMVARI not transmitting

[Bob Wilson, N6TV]

>From 2.0.12 release notes:

- MMVARI new options added: Sound card RX, Sound card TX.
  Allows user to choose which sound card will be used for RX and TX in each of
the MMVARI Radio windows.
  Default value is windows default sound card setting.

Did you do set anything under the DXLog.net Options menu to auto-start
MMVARI and select the sound card there?

73,
Bob, N6TV

On Wed, Sep 25, 2013 at 4:41 PM, David Ross <drossm at sympatico.ca> wrote:

> In the stand alone MMVARI application I can transmit setting the Soundcard
> Input to the Microphone USB Audio CODEC and Output to the Speakers USB
> Audio CODEC. Then selecting PTT under DTR/RTS in the Radio Command Setup.
>
> In DXLog there is no selection for the Microphone USB Audio CODEC. That
> appears to be the cause of not getting MMVARI in DXLog to transmit.
>
> I would really like to get MMVARI in DXLog to transmit.
>
> David  VA3MJR
>
> > From: n6tv at arrl.net
> > Date: Wed, 25 Sep 2013 15:35:51 -0700
> > To: support at dxlog.net
> > Subject: Re: [DXLog.net - Support] DXLog MMVARI not transmitting
> >
> > In MMVARI, Option | Setup.  In the TX tab, did you set PTT to anything or
> > does it say "NONE"?  Maybe you need to make MMVARI control PTT rather
> than
> > DXLog.net.
> >
> > 73,
> > Bob, N6TV
> >
> > On Wed, Sep 25, 2013 at 3:06 PM, David Ross <drossm at sympatico.ca> wrote:
> >
> > > Had the settings correct except for the Baud, was 9600 and now 4800
> and I
> > > now have CAT control but still not transmitting in MMVARI.
> > >
> > > David  VA3MJR
> > >
> > >
> > >
> > > > From: n6tv at arrl.net
> > > > Date: Wed, 25 Sep 2013 14:35:30 -0700
> > > > To: support at dxlog.net
> > > > Subject: Re: [DXLog.net - Support] DXLog MMVARI not transmitting
> > > >
> > > > On Wed, Sep 25, 2013 at 11:25 AM, David Ross <drossm at sympatico.ca>
> > > wrote:
> > > >
> > > > >
> > > > > DXLog is still not reading either VFO frequencies
> > > > >
> > > >
> > > > David,
> > > >
> > > > What have you tried to do so far?  Did you look at menu 027 to see
> what
> > > > baud rate your radio is using?  Default is 4800.  I suggest setting
> menu
> > > > 029 (CAT RTS) to OFF.  Then just set up the radio's COM port in
> DXLog.net
> > > > to the same values:  4800,N,8,2, Always OFF, Always OFF.
> > > >
> > > > 73,
> > > > Bob, N6TV
> > > > _______________________________________________
> > > > Support mailing list
> > > > Support at dxlog.net
> > > > http://www.dxlog.net/mailman/listinfo/support
> > >
> > > _______________________________________________
> > > Support mailing list
> > > Support at dxlog.net
> > > http://www.dxlog.net/mailman/listinfo/support
> > >
> > _______________________________________________
> > Support mailing list
> > Support at dxlog.net
> > http://www.dxlog.net/mailman/listinfo/support
>
> _______________________________________________
> Support mailing list
> Support at dxlog.net
> http://www.dxlog.net/mailman/listinfo/support
>