[DXLog.net - Support] DXLog MMVARI not transmitting

David Ross drossm at sympatico.ca
Thu Sep 26 01:59:20 CEST 2013


I do not see anything under  the DXLog.net Options menu to auto-start
MMVARI and select any sound card there.

David  VA3MJR

> From: n6tv at arrl.net
> Date: Wed, 25 Sep 2013 16:49:15 -0700
> To: support at dxlog.net
> Subject: Re: [DXLog.net - Support] DXLog MMVARI not transmitting
> 
> From 2.0.12 release notes:
> 
> - MMVARI new options added: Sound card RX, Sound card TX.
>   Allows user to choose which sound card will be used for RX and TX in each of
> the MMVARI Radio windows.
>   Default value is windows default sound card setting.
> 
> Did you do set anything under the DXLog.net Options menu to auto-start
> MMVARI and select the sound card there?
> 
> 73,
> Bob, N6TV
> 
> On Wed, Sep 25, 2013 at 4:41 PM, David Ross <drossm at sympatico.ca> wrote:
> 
> > In the stand alone MMVARI application I can transmit setting the Soundcard
> > Input to the Microphone USB Audio CODEC and Output to the Speakers USB
> > Audio CODEC. Then selecting PTT under DTR/RTS in the Radio Command Setup.
> >
> > In DXLog there is no selection for the Microphone USB Audio CODEC. That
> > appears to be the cause of not getting MMVARI in DXLog to transmit.
> >
> > I would really like to get MMVARI in DXLog to transmit.
> >
> > David  VA3MJR
> >
> > > From: n6tv at arrl.net
> > > Date: Wed, 25 Sep 2013 15:35:51 -0700
> > > To: support at dxlog.net
> > > Subject: Re: [DXLog.net - Support] DXLog MMVARI not transmitting
> > >
> > > In MMVARI, Option | Setup.  In the TX tab, did you set PTT to anything or
> > > does it say "NONE"?  Maybe you need to make MMVARI control PTT rather
> > than
> > > DXLog.net.
> > >
> > > 73,
> > > Bob, N6TV
> > >
> > > On Wed, Sep 25, 2013 at 3:06 PM, David Ross <drossm at sympatico.ca> wrote:
> > >
> > > > Had the settings correct except for the Baud, was 9600 and now 4800
> > and I
> > > > now have CAT control but still not transmitting in MMVARI.
> > > >
> > > > David  VA3MJR
> > > >
> > > >
> > > >
> > > > > From: n6tv at arrl.net
> > > > > Date: Wed, 25 Sep 2013 14:35:30 -0700
> > > > > To: support at dxlog.net
> > > > > Subject: Re: [DXLog.net - Support] DXLog MMVARI not transmitting
> > > > >
> > > > > On Wed, Sep 25, 2013 at 11:25 AM, David Ross <drossm at sympatico.ca>
> > > > wrote:
> > > > >
> > > > > >
> > > > > > DXLog is still not reading either VFO frequencies
> > > > > >
> > > > >
> > > > > David,
> > > > >
> > > > > What have you tried to do so far?  Did you look at menu 027 to see
> > what
> > > > > baud rate your radio is using?  Default is 4800.  I suggest setting
> > menu
> > > > > 029 (CAT RTS) to OFF.  Then just set up the radio's COM port in
> > DXLog.net
> > > > > to the same values:  4800,N,8,2, Always OFF, Always OFF.
> > > > >
> > > > > 73,
> > > > > Bob, N6TV
> > > > > _______________________________________________
> > > > > Support mailing list
> > > > > Support at dxlog.net
> > > > > http://www.dxlog.net/mailman/listinfo/support
> > > >
> > > > _______________________________________________
> > > > Support mailing list
> > > > Support at dxlog.net
> > > > http://www.dxlog.net/mailman/listinfo/support
> > > >
> > > _______________________________________________
> > > Support mailing list
> > > Support at dxlog.net
> > > http://www.dxlog.net/mailman/listinfo/support
> >
> > _______________________________________________
> > Support mailing list
> > Support at dxlog.net
> > http://www.dxlog.net/mailman/listinfo/support
> >
> _______________________________________________
> Support mailing list
> Support at dxlog.net
> http://www.dxlog.net/mailman/listinfo/support
 		 	   		  


More information about the Support mailing list