Difference between revisions of "Radios and Peripherals"

From DXLog.net
Jump to navigation Jump to search
(Lab 599)
(SO2V operation)
(36 intermediate revisions by the same user not shown)
Line 12: Line 12:
 
Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.
 
Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.
  
===KX2, KX3, K3, K3S, and K4===
+
===KX2, KX3, K3, and K4===
  
 
The recommended CAT interface setting is 38400bps, 8 bit, no parity, 1 stop bit, and 300ms polling interval.  
 
The recommended CAT interface setting is 38400bps, 8 bit, no parity, 1 stop bit, and 300ms polling interval.  
Line 18: Line 18:
 
Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.
 
Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.
  
For SO2V operation with K3/K3S <u>without</u> sub receiver, KX2, or KX3 the menu option <br>
+
For SO2V operation with K3 or K4 <u>without</u> sub receiver, KX2, or KX3 the menu option <br>
 
<code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be <u>disabled</u>.  
 
<code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be <u>disabled</u>.  
  
For K3/K3S/K4 <u>with</u> a sub receiver, this option should be <u>enabled</u>. Sub receiver control is supported.<br>
+
For K3 or K4 <u>with</u> a sub receiver, this option should be <u>enabled</u>. Sub receiver control is supported.<br>
 
For more information, see [[Menu_Operating#Technique|Operating techniques]].
 
For more information, see [[Menu_Operating#Technique|Operating techniques]].
  
When recording voice messages for the internal voice keyer on KX2 and KX3, recording should be started by pressing the <code>XMIT</code> button on <br>
+
When recording voice messages for the internal voice keyer on KX2 and KX3, recording must be started by pressing the<br>
the radio but completed by pressing ESC on the computer's keyboard.  
+
<code>XMIT</code> button on the radio but can be completed by pressing ESC on the computer's keyboard.  
  
To make the CW sidetone or transmitted audio available for the contest recorder on a K3/K3S/K4 (e.g. routed via an SO2R controller) you need to<br>  
+
To make the CW side tone or transmitted audio available for the contest recorder on a K3 and K4 (e.g. routed via an SO2R controller)<br>
select LIN OUT from the menu, press 2, and then set the transmit monitor level there.  
+
you need to select <tt>LIN OUT</tt> from the menu, press 2, and then set the transmit monitor level there.  
  
For K3/K3S/K4 <u>with</u> sub receiver, coherent diversity operation is supported. It can either be enabled/disabled by pressing<br>
+
For K3 and K4 radios <u>with</u> sub receiver, coherent diversity operation is supported. It can either be enabled/disabled by pressing<br>
 
<code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or with a long press on the radio's <code>SUB</code> button.<br>
 
<code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or with a long press on the radio's <code>SUB</code> button.<br>
 
Diversity is indicated with a <code>DIV</code> icon below in the "seven segment" frequency counter in<br>
 
Diversity is indicated with a <code>DIV</code> icon below in the "seven segment" frequency counter in<br>
 
the radio/band map window.
 
the radio/band map window.
 +
 +
==FlexRadio==
 +
 +
Since FlexRadio uses a completely virtual serial port, port speed has no meaning.<br>
 +
A polling interval of 200ms will give a good user experience.
 +
 +
Keyboard RIT is supported but only on VFO A.
 +
 +
When using DXLog's internal DVK, DAX is switched on at the beginning of playback and then<br>
 +
switched off at the end. This is to support the use of the DVK also with remote operation<br>
 +
when DAX is used for the microphone signal.
 +
 +
===SO2V operation===
 +
 +
The option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
 +
 +
Make sure to select SO2V and disable "Auto Switch TX slice" for '''all''' interfaces in the<br>
 +
CAT setup panel as shown below. If this is not done, slice B will be closed down when not focused<br>
 +
and transmission will always be on slice A.
 +
 +
"Subreceiver" on/off control is supported.
 +
 +
 +
[[image:flexso2vcat.png]]
  
 
==ICOM==
 
==ICOM==
Line 42: Line 66:
 
For radios listed below but with old firmware, chose IC-7000 but use the radio model's correct CI-V address.<br>
 
For radios listed below but with old firmware, chose IC-7000 but use the radio model's correct CI-V address.<br>
 
This may also be necessary when using outdated equipment that rely on information on the CI-V interface,<br>
 
This may also be necessary when using outdated equipment that rely on information on the CI-V interface,<br>
such as power amplifiers or band decoders.
+
such as power amplifiers or band decoders. The radio model's default CI-V address is displayed in the text<br>
 +
box "ICOM CI-V address (hex)" in the radio settings panel when the radio model is selected.
  
===IC-7300, IC-7610, IC-7850, IC-7851, IC-9700===
+
===IC-7300, IC-7610, IC-7850, IC-7851, and IC-9700===
  
 
Even if you are using a station controller such as a microHAM MK2R+ you will get a better user experience if you <br>
 
Even if you are using a station controller such as a microHAM MK2R+ you will get a better user experience if you <br>
Line 52: Line 77:
 
In DXLog's radio settings, select the relevant COM port, chose 100ms polling interval and set the interface to <br>
 
In DXLog's radio settings, select the relevant COM port, chose 100ms polling interval and set the interface to <br>
 
115200bps, 8 bits, no parity and 1 stop bit.
 
115200bps, 8 bits, no parity and 1 stop bit.
 +
 +
Due to limitations in ICOM's CI-V protocol, changes in VFO selection made using the radio's controls on<br>
 +
IC-7300 and IC-9700 will not be correctly recognized by DXLog.
  
 
On the radio, go to the CI-V menu by selecting:<br>
 
On the radio, go to the CI-V menu by selecting:<br>
Line 62: Line 90:
  
 
For SO2V operation the menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> <br>
 
For SO2V operation the menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> <br>
should be <u>disabled</u> for IC-705, IC-7300, and IC-9700. It should be <u>enabled</u> for IC-7610, IC-7850, and IC-7851.  
+
should be <u>disabled</u> for IC-7300 and IC-9700. It should be <u>enabled</u> for IC-7610, IC-7850, and IC-7851.  
  
With this option <u>enabled</u>, sub receiver and VFO knob focus control are supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].<br>
+
With this option <u>enabled</u>, sub receiver and VFO knob focus control are supported. For more information, see<br>
Please note that if sub receiver and VFO knob focus control is used with a low CAT speed (e.g. 19200bps)<br>
+
[[Menu_Operating#Technique|Operating techniques]]. Please note that if sub receiver and VFO knob focus control<br>
the polling interval will have to be increased to about 400ms to secure responsiveness when switching focus in DXLog.  
+
is used with a low CI-V speed (e.g. 19200bps) the polling interval will have to be increased to about 400ms to<br>
 +
secure responsiveness when switching focus in DXLog. This is to make sure sufficient CI-V bus bandwidth is available<br>
 +
for the commands.
  
 
The internal voice keyer is supported but only for playback. Recording has to be done using the radio's recording menu.<br>
 
The internal voice keyer is supported but only for playback. Recording has to be done using the radio's recording menu.<br>
Line 72: Line 102:
 
The eighth voice keyer memory is accessible via the <tt>$PBINS</tt> macro.  
 
The eighth voice keyer memory is accessible via the <tt>$PBINS</tt> macro.  
  
'''NB.''' ICOM CI-V is a semi-duplex protocol that both transmits and receives using a single line. Using <code>CI-V Transceive = ON</code> at<br>
+
'''NB.''' ICOM CI-V is a semi-duplex protocol that both transmits and receives using a single line.<br>
lower speeds with a basic USB-to-serial interface may create message collisions causing DXLog's CAT driver to briefly pause while recovering<br>
+
Using <code>CI-V Transceive = ON</code> together with polling and lower speeds with a basic USB-to-serial interface<br>
from the collision. This is not an error. This will however not happen when using the radio's USB interface or a protocol-aware serial interface,<br>
+
may create message collisions causing DXLog's CAT driver to briefly pause while recovering from the collision.<br>
such as a microHAM keyer/controller.
+
This is not an error. This will however not happen when using the radio's own USB interface or a protocol-aware<br>
 +
serial interface, such as a microHAM keyer/controller.
  
The radio's default setting is to not include CW sidetone or transmit audio in the radio's audio output.<br>
+
The radio's default setting is to not include CW side tone or transmit audio in the radio's audio output.<br>
 
For e.g. recording a contest, this needs to be activated.  
 
For e.g. recording a contest, this needs to be activated.  
  
Line 85: Line 116:
 
: <tt>SET -> Connectors -> ACC AF/IF Output -> AF Beep/Speech... Output = ON</tt>
 
: <tt>SET -> Connectors -> ACC AF/IF Output -> AF Beep/Speech... Output = ON</tt>
  
Coherent diversity ("Tracking") is supported on IC-7610, IC-7850, and IC-7851. It can either be enabled/disabled from the keyboard with <br>
+
Coherent diversity ("Tracking") is supported on IC-7610, IC-7850, and IC-7851. It can either be enabled/disabled from  
<code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or by a long press on the radio's <code>MAIN/SUB</code> button.<br>
+
the keyboard with <code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or by a long press on the radio's <code>MAIN/SUB</code> button.<br>
Diversity is indicated with a <code>DIV</code> icon below in the "seven segment" frequency counter in the radio/band map window.
+
Diversity is indicated with a <code>DIV</code> icon below in the "seven segment" frequency counter in the radio/band<br>
 +
map window.
  
 
'''NB.''' On ICOM radios, RIT is not supported in diversity mode. Coherency is lost when the RIT is adjusted.<br>
 
'''NB.''' On ICOM radios, RIT is not supported in diversity mode. Coherency is lost when the RIT is adjusted.<br>
Line 100: Line 132:
 
Since both the USB and Bluetooth COM ports are virtual, they speed setting is ignored. However, since the latency in<br>
 
Since both the USB and Bluetooth COM ports are virtual, they speed setting is ignored. However, since the latency in<br>
 
the Bluetooth interface is considerable it is important to not chose too short a polling period. Above 200ms is a good number.
 
the Bluetooth interface is considerable it is important to not chose too short a polling period. Above 200ms is a good number.
 +
 +
Due to limitations in ICOM's CI-V protocol, changes in VFO selection made using the radio's controls<br>
 +
will not be correctly recognized by DXLog.
  
 
When using USB, select the relevant COM port, chose 100ms polling interval and set the interface to <br>
 
When using USB, select the relevant COM port, chose 100ms polling interval and set the interface to <br>
115200bps, 8 bits, no parity and 1 stop bit.
+
115200bps, 8 bits, no parity and 1 stop bit. Enabling "Transceive" also when not using "ICOM CI-V mode" in<br>
 +
the radio settings will improve the user experience somewhat.
  
 
For SO2V operation the menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> <br>
 
For SO2V operation the menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> <br>
Line 114: Line 150:
 
For e.g. recording a contest, this needs to be activated. C.f. the above section for instructions.
 
For e.g. recording a contest, this needs to be activated. C.f. the above section for instructions.
  
===IC-7600, IC-7700, IC-7800===
+
===IC-7600, IC-7700, and IC-7800===
  
Use the highest available speed on the CI-V interface (19200bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 500ms.  
+
Use the highest available speed on the CI-V interface (19200bps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 400ms.  
  
For SO2V operation with IC-7800 the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
As a rule, <code>CI-V Transceive</code> should be disabled in the radio's set up menu.  
  
For SO2V operation with IC-7600 and IC-7700 the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
However, by enabling it and checking the <i>Use ICOM CI-V mode</i> option in the radio set up you will get a<br>
 +
<b>much</b> better user experience at low CAT interface speeds. Be aware, however, that since DXLog is not polling the<br>
 +
radio in this mode, changes to RIT, SPLIT, and VFO selection made on the radio's controls will not be recognized by DXLog.
 +
 
 +
The menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code><br>
 +
should be <u>enabled</u> for SO2V operation with IC-7800 and <u>disabled</u> for IC-7600 and IC-7700.  
  
 
With this option <u>enabled</u>, sub receiver and VFO knob focus control are supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].<br>
 
With this option <u>enabled</u>, sub receiver and VFO knob focus control are supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].<br>
 
As a rule, <i>CI-V Transceive</i> should be disabled in the radio's set up menu.
 
 
However, by enabling it and checking the <i>Use ICOM CI-V mode</i> option in the radio set up you will get a much better user experience at low CAT interface speeds.<br>
 
Be aware, however, that since DXLog is not polling the radio, e.g. RIT and SPLIT changes made on the radio's controls will not be recognized by DXLog.
 
  
 
Since the radio lacks the ability to control the internal voice keyer via CI-V, it is not supported.
 
Since the radio lacks the ability to control the internal voice keyer via CI-V, it is not supported.
Line 144: Line 181:
 
Firmware releases can be found on [https://www.kenwood.com/i/products/info/amateur/software_download.html Kenwood's firmware web site].
 
Firmware releases can be found on [https://www.kenwood.com/i/products/info/amateur/software_download.html Kenwood's firmware web site].
  
===TS-480SAT, TS-480HX===
+
===TS-2000===
  
Use the highest reliable speed on the CAT interface (38400-115200bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Use the highest reliable speed on the CAT interface (19200ps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 300ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
The internal voice keyer is supported but only for playback.
 
The internal voice keyer is supported but only for playback.
 +
 +
Different mode on VFO A and VFO B is not supported.
 +
 +
===TS-480SAT and TS-480HX===
 +
 +
Use the highest reliable speed on the CAT interface (up to 115200bps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 200ms.
 +
 +
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
 +
 +
The internal voice keyer is supported but only for playback.
 +
 +
Different mode on VFO A and VFO B is not supported.
  
 
===TS-590S===
 
===TS-590S===
  
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 200ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
The internal voice keyer is supported but only for playback.
 
The internal voice keyer is supported but only for playback.
Line 164: Line 216:
 
===TS-890S===
 
===TS-890S===
  
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 200ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
The internal voice keyer is supported but only for playback.
 
The internal voice keyer is supported but only for playback.
Line 172: Line 225:
 
===TS-990S===
 
===TS-990S===
  
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).<br>
 +
A suitable polling interval is 200ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
  
 
Subreceiver control is supported.
 
Subreceiver control is supported.
Line 186: Line 240:
 
Use the highest available speed on the CAT interface. A suitable polling period at 4800bps is 500ms.  
 
Use the highest available speed on the CAT interface. A suitable polling period at 4800bps is 500ms.  
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
Depending on radio model, the internal voice keyer may be supported. If so, only for playback.
 
Depending on radio model, the internal voice keyer may be supported. If so, only for playback.
  
==Lab 599==
+
==Lab599==
 +
 
 +
For best performance with DXLog your radio needs to have the most recent firmware.<br>
 +
Firmware releases can be found on [https://lab599.com/downloads Lab599's web site].
  
 
===Discovery TX-500===
 
===Discovery TX-500===
  
 
Select 9600bps, 8 data bits, no parity, and one stop bit. A suitable polling interval is 300ms.
 
Select 9600bps, 8 data bits, no parity, and one stop bit. A suitable polling interval is 300ms.
 +
 +
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
Keyboard RIT is not supported.
 
Keyboard RIT is not supported.
  
==Yaesu==
+
==microHAM==
 +
 
 +
Make sure to always use the latest version of the USB Device Router which can be downloaded from [https://www.microham.com/index.html microHAM's website].
 +
 
 +
This will also contain the latest firmware for your microHAM devices.
 +
 
 +
===PTT lead time===
 +
 
 +
The PTT lead time set in DXLog is only active for COM-port keying. For Winkey keying, the PTT<br>
 +
lead time must be set in the keyer's PTT tab in microHAM device router.<br>
 +
This is even if "allow logger control" is checked in device router's CW/WinKey panel.
 +
 
 +
===RTTY FSK===
 +
 
 +
Even modern radios with built-in virtual COM ports only have only one COM-port for FSK keying.<br>
 +
This means SO2V RTTY is not really possible.
 +
 
 +
However, using a microHAM keyer such as MK2R+ you have two virtual COM ports for FSK which means it is possible.
 +
 
 +
'''NB.''' Disable "Stuff" for the FSK COM-port in the USB Device Router's Ports tab or your transmission may be distorted.
  
For best performance with DXLog your radio needs to have the most recent firmware.<br>
+
===Foot pedal===
Firmware releases can be found on [https://www.yaesu.com Yaesu's web site].
 
  
===FT-450D===
+
Although DXLog supports multiple uses for a footpedal connected to a COM-port, a foot pedal connected<br>
 +
to a microHAM keyer can only serve as PTT.
  
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
'''NB.''' On microHAM keyers, DXLog does not recognize foot pedal 1 and foot pedal 2. Both act as PTT<br>
 +
for the currently focused radio.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
==Yaesu==
  
The internal voice keyer is supported for both playback and recording.  
+
For best performance with DXLog your radio needs to have the most recent firmware.<br>
 +
Firmware releases can be found on [https://www.yaesu.com Yaesu's web site].
  
 
===FT-817ND, 818, 847, 857D, and 897===
 
===FT-817ND, 818, 847, 857D, and 897===
  
Use the highest available speed on the CAT interface (38400bps or 57600bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits). A suitable polling interval is 300ms.
+
Use the highest available speed on the CAT interface (38400bps or 57600bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 300ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
 
VFO B control is supported by DXLog but due to limitations in the radios' CAT protocol changes in VFO selection or<br>
 
VFO B control is supported by DXLog but due to limitations in the radios' CAT protocol changes in VFO selection or<br>
Line 226: Line 307:
 
Note that the CAT interface uses 2 (<b>TWO</b>) stop bits.  
 
Note that the CAT interface uses 2 (<b>TWO</b>) stop bits.  
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
  
 
Subreceiver control is not supported.
 
Subreceiver control is not supported.
Line 232: Line 313:
 
The internal voice keyer is not supported.
 
The internal voice keyer is not supported.
  
===FT-1000MP, FT-1000MKV===
+
===FT-1000MP and FT-1000MKV===
  
 
Use the highest available speed on the CAT interface. (At 4800bps a suitable polling interval is 500ms.)
 
Use the highest available speed on the CAT interface. (At 4800bps a suitable polling interval is 500ms.)
Line 238: Line 319:
 
Note that the CAT interface uses 2 (<b>TWO</b>) stop bits.  
 
Note that the CAT interface uses 2 (<b>TWO</b>) stop bits.  
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
  
 
Subreceiver control is supported.
 
Subreceiver control is supported.
Line 244: Line 325:
 
The internal voice keyer is not supported.
 
The internal voice keyer is not supported.
  
===FTDX1200, FTDX3000===
+
===FT-450D===
  
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 100ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
The internal voice keyer is supported but only for playback.
+
The internal voice keyer is supported for both recording and playback.
  
===FTDX5000===
+
===FTDX1200 and FTDX3000===
  
Due to lack of access the support status for Yaesu FTDX5000 is currently unclear.
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 200ms.
  
The current driver is largely similar to that for FTDX3000 and should provide basic functionality.
+
For the FTDX3000 the USB CAT interface is strongly recommended.
  
The development team is looking for owners of this radio.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
===FTDX101D===
+
The internal voice keyer is supported but only for playback.
 +
 
 +
===FTDX5000===
  
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 1 stop bit). A suitable polling interval is 200ms.
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 200ms.
  
For SO2V operation the DXLog menu option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
  
 
With this option <u>enabled</u>, sub receiver control is supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].
 
With this option <u>enabled</u>, sub receiver control is supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].
  
The internal voice keyer is supported both for playback and recording.
+
The internal voice keyer is supported but only for playback.
  
Coherent diversity is supported. It can either be enabled/disabled from the keyboard with <code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or with a long press <br>
+
===FT-991 and FT-991A===
on the radio's <code>SYNC</code> button. Diversity is indicated with a <code>DIV</code> icon right below in the "seven segment" frequency counter in the radio/band map window.
 
  
==FlexRadio==
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 100ms.
  
Since FlexRadio uses a completely virtual serial port, port speed has no meaning.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
A polling interval of 200ms will give a good user experience.
 
  
Keyboard RIT is supported but only on VFO A.
+
The internal voice keyer is not supported.  
  
When using DXLog's internal DVK, DAX is switched on at the beginning of playback and then<br>
+
===FTDX101D===
switched off at the end. This is to support the use of the DVK also with remote operation<br>
 
when DAX is used for the microphone signal.
 
  
===SO2V operation===
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 200ms.
  
The option <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
+
Using the virtual COM port via USB is recommended.
  
Make sure to enable SO2V in the CAT setup panel as shown below.
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be enabled.
If this is not done, slice B will be closed down when not focused.  
 
  
"Subreceiver" on/off control is supported.
+
With this option <u>enabled</u>, sub receiver control is supported. For more information, see [[Menu_Operating#Technique|Operating techniques]].
  
 +
The internal voice keyer is supported both for playback and recording.
  
[[image:flexso2vcat.png]]
+
Coherent diversity is supported. It can either be enabled/disabled from the keyboard with <code>[Ctrl][-]</code> or <code>[Ctrl][Keypad Subtract]</code> or with a long press <br>
 +
on the radio's <code>SYNC</code> button. Diversity is indicated with a <code>DIV</code> icon right below in the "seven segment" frequency counter in the radio/band map window.
  
==microHAM==
+
===FTDX10===
  
Make sure to always use the latest version of the USB Device Router which can be downloaded from [https://www.microham.com/index.html microHAM's website].
+
<b>NB. Due to the newness of the radio model and lack of access, DXLog's driver is in an experimental state.</b>
  
This will also contain the latest firmware for your microHAM devices.
+
Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (<b>TWO</b>) stop bits).<br>
 +
A suitable polling interval is 200ms.
  
===RTTY FSK===
+
For SO2V operation, <code>Options|Interface specific options|Use SPLIT command in SO2V technique</code> should be disabled.
  
Even modern radios with built-in virtual COM ports only have only one COM-port for FSK keying.<br>
+
The internal voice keyer is not supported.
This means SO2V RTTY is not really possible.
 
 
 
However, using a microHAM keyer such as MK2R+ you have two virtual COM ports for FSK which means it is possible.
 
 
 
'''NB.''' Disable "Stuff" for the FSK COM-port in the USB Device Router's Ports tab or your transmission may be corrupted.
 
 
 
===Foot pedal===
 
 
 
Although DXLog supports multiple uses for a footpedal connected to a COM-port, a foot pedal connected<br>
 
to a microHAM keyer can only serve as PTT.
 
 
 
'''NB.''' On microHAM keyers, DXLog does not recognize foot pedal 1 and foot pedal 2. Both act as PTT<br>
 
for the currently focused radio.
 

Revision as of 15:36, 28 November 2020

Elecraft

For best performance with DXLog your radio needs to have the most recent firmware.
Firmware releases can be found on Elecraft's firmware web site.

K2

The recommended CAT interface setting is 4800bps, 8 bit, no parity, 1 stop bit, and 300ms polling interval.

For SO2V operation the menu option Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.

KX2, KX3, K3, and K4

The recommended CAT interface setting is 38400bps, 8 bit, no parity, 1 stop bit, and 300ms polling interval.

Per Elecraft recommendations, the option "Do not poll radio during TX" in DXLog's radio settings should be checked.

For SO2V operation with K3 or K4 without sub receiver, KX2, or KX3 the menu option
Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

For K3 or K4 with a sub receiver, this option should be enabled. Sub receiver control is supported.
For more information, see Operating techniques.

When recording voice messages for the internal voice keyer on KX2 and KX3, recording must be started by pressing the
XMIT button on the radio but can be completed by pressing ESC on the computer's keyboard.

To make the CW side tone or transmitted audio available for the contest recorder on a K3 and K4 (e.g. routed via an SO2R controller)
you need to select LIN OUT from the menu, press 2, and then set the transmit monitor level there.

For K3 and K4 radios with sub receiver, coherent diversity operation is supported. It can either be enabled/disabled by pressing
[Ctrl][-] or [Ctrl][Keypad Subtract] or with a long press on the radio's SUB button.
Diversity is indicated with a DIV icon below in the "seven segment" frequency counter in
the radio/band map window.

FlexRadio

Since FlexRadio uses a completely virtual serial port, port speed has no meaning.
A polling interval of 200ms will give a good user experience.

Keyboard RIT is supported but only on VFO A.

When using DXLog's internal DVK, DAX is switched on at the beginning of playback and then
switched off at the end. This is to support the use of the DVK also with remote operation
when DAX is used for the microphone signal.

SO2V operation

The option Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

Make sure to select SO2V and disable "Auto Switch TX slice" for all interfaces in the
CAT setup panel as shown below. If this is not done, slice B will be closed down when not focused
and transmission will always be on slice A.

"Subreceiver" on/off control is supported.


Flexso2vcat.png

ICOM

For best performance with DXLog your radio needs to have the most recent firmware.
Firmware releases can be found on ICOM's firmware web site.

For radios listed below but with old firmware, chose IC-7000 but use the radio model's correct CI-V address.
This may also be necessary when using outdated equipment that rely on information on the CI-V interface,
such as power amplifiers or band decoders. The radio model's default CI-V address is displayed in the text
box "ICOM CI-V address (hex)" in the radio settings panel when the radio model is selected.

IC-7300, IC-7610, IC-7850, IC-7851, and IC-9700

Even if you are using a station controller such as a microHAM MK2R+ you will get a better user experience if you
let DXLog control the radio directly via the high speed USB interface. (The station controller should however
still be connected to the radio's "REMOTE" interface for correct band and mode decoding.)

In DXLog's radio settings, select the relevant COM port, chose 100ms polling interval and set the interface to
115200bps, 8 bits, no parity and 1 stop bit.

Due to limitations in ICOM's CI-V protocol, changes in VFO selection made using the radio's controls on
IC-7300 and IC-9700 will not be correctly recognized by DXLog.

On the radio, go to the CI-V menu by selecting:
MENU->SET->Connectors->CI-V
Then set
CI-V Transceive = ON (Optional)
CI-V USB Port = Unlink from [REMOTE]
CI-V USB Baud Rate = 115200
CI-V USB Echo Back = OFF

For SO2V operation the menu option Options|Interface specific options|Use SPLIT command in SO2V technique
should be disabled for IC-7300 and IC-9700. It should be enabled for IC-7610, IC-7850, and IC-7851.

With this option enabled, sub receiver and VFO knob focus control are supported. For more information, see
Operating techniques. Please note that if sub receiver and VFO knob focus control
is used with a low CI-V speed (e.g. 19200bps) the polling interval will have to be increased to about 400ms to
secure responsiveness when switching focus in DXLog. This is to make sure sufficient CI-V bus bandwidth is available
for the commands.

The internal voice keyer is supported but only for playback. Recording has to be done using the radio's recording menu.
All eight voice keyer memories in the radio are supported and available from function keys [F1] through [F7].
The eighth voice keyer memory is accessible via the $PBINS macro.

NB. ICOM CI-V is a semi-duplex protocol that both transmits and receives using a single line.
Using CI-V Transceive = ON together with polling and lower speeds with a basic USB-to-serial interface
may create message collisions causing DXLog's CAT driver to briefly pause while recovering from the collision.
This is not an error. This will however not happen when using the radio's own USB interface or a protocol-aware
serial interface, such as a microHAM keyer/controller.

The radio's default setting is to not include CW side tone or transmit audio in the radio's audio output.
For e.g. recording a contest, this needs to be activated.

When using the built-in USB sound card:

SET -> Connectors -> USB AF/IF Output -> AF Beep/Speech... Output = ON

When using the ACC connector (e.g. when routing audio through an SO2R controller)

SET -> Connectors -> ACC AF/IF Output -> AF Beep/Speech... Output = ON

Coherent diversity ("Tracking") is supported on IC-7610, IC-7850, and IC-7851. It can either be enabled/disabled from the keyboard with [Ctrl][-] or [Ctrl][Keypad Subtract] or by a long press on the radio's MAIN/SUB button.
Diversity is indicated with a DIV icon below in the "seven segment" frequency counter in the radio/band
map window.

NB. On ICOM radios, RIT is not supported in diversity mode. Coherency is lost when the RIT is adjusted.
However, with DXLog RIT is supported. DXLog will automatically adjust the sub VFO to the same
frequency as the main VFO with RIT offset.

IC-705

The IC-705 lacks a traditional, serial CI-V interface. The two options for logger control are via a virtual COM port either via USB or Bluetooth.

Since both the USB and Bluetooth COM ports are virtual, they speed setting is ignored. However, since the latency in
the Bluetooth interface is considerable it is important to not chose too short a polling period. Above 200ms is a good number.

Due to limitations in ICOM's CI-V protocol, changes in VFO selection made using the radio's controls
will not be correctly recognized by DXLog.

When using USB, select the relevant COM port, chose 100ms polling interval and set the interface to
115200bps, 8 bits, no parity and 1 stop bit. Enabling "Transceive" also when not using "ICOM CI-V mode" in
the radio settings will improve the user experience somewhat.

For SO2V operation the menu option Options|Interface specific options|Use SPLIT command in SO2V technique
should be disabled.

The internal voice keyer is supported but only for playback. Recording has to be done using the radio's recording menu.
All eight voice keyer memories in the radio are supported and available from function keys [F1] through [F7].
The eighth voice keyer memory is accessible via the $PBINS macro.

The radio's default setting is to not include CW sidetone or transmit audio in the radio's audio output.
For e.g. recording a contest, this needs to be activated. C.f. the above section for instructions.

IC-7600, IC-7700, and IC-7800

Use the highest available speed on the CI-V interface (19200bps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 400ms.

As a rule, CI-V Transceive should be disabled in the radio's set up menu.

However, by enabling it and checking the Use ICOM CI-V mode option in the radio set up you will get a
much better user experience at low CAT interface speeds. Be aware, however, that since DXLog is not polling the
radio in this mode, changes to RIT, SPLIT, and VFO selection made on the radio's controls will not be recognized by DXLog.

The menu option Options|Interface specific options|Use SPLIT command in SO2V technique
should be enabled for SO2V operation with IC-7800 and disabled for IC-7600 and IC-7700.

With this option enabled, sub receiver and VFO knob focus control are supported. For more information, see Operating techniques.

Since the radio lacks the ability to control the internal voice keyer via CI-V, it is not supported.

Older ICOM

Use the highest available speed on the CI-V interface. 400ms polling interval is recommended.

For a better user experience, Enable ICOM CI-V mode in DXLog's radio settings and enable "Transceive" in the radio's menu if available.

SO2V operation is only partially supported since older versions of the CI-V protocol does not allow access to VFO B.

Kenwood

For best performance with DXLog your radio needs to have the most recent firmware.
Firmware releases can be found on Kenwood's firmware web site.

TS-2000

Use the highest reliable speed on the CAT interface (19200ps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 300ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported but only for playback.

Different mode on VFO A and VFO B is not supported.

TS-480SAT and TS-480HX

Use the highest reliable speed on the CAT interface (up to 115200bps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported but only for playback.

Different mode on VFO A and VFO B is not supported.

TS-590S

Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported but only for playback.

Different mode on VFO A and VFO B is not supported.

TS-890S

Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported but only for playback.

TS-990S

Preferably use the USB CAT interface at the highest available speed (115200bps, 8 bits, no parity, 1 stop bit).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

Subreceiver control is supported.

The internal voice keyer is supported but only for playback.

Older Kenwood

Use the generic driver called "Kenwood".

Use the highest available speed on the CAT interface. A suitable polling period at 4800bps is 500ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

Depending on radio model, the internal voice keyer may be supported. If so, only for playback.

Lab599

For best performance with DXLog your radio needs to have the most recent firmware.
Firmware releases can be found on Lab599's web site.

Discovery TX-500

Select 9600bps, 8 data bits, no parity, and one stop bit. A suitable polling interval is 300ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

Keyboard RIT is not supported.

microHAM

Make sure to always use the latest version of the USB Device Router which can be downloaded from microHAM's website.

This will also contain the latest firmware for your microHAM devices.

PTT lead time

The PTT lead time set in DXLog is only active for COM-port keying. For Winkey keying, the PTT
lead time must be set in the keyer's PTT tab in microHAM device router.
This is even if "allow logger control" is checked in device router's CW/WinKey panel.

RTTY FSK

Even modern radios with built-in virtual COM ports only have only one COM-port for FSK keying.
This means SO2V RTTY is not really possible.

However, using a microHAM keyer such as MK2R+ you have two virtual COM ports for FSK which means it is possible.

NB. Disable "Stuff" for the FSK COM-port in the USB Device Router's Ports tab or your transmission may be distorted.

Foot pedal

Although DXLog supports multiple uses for a footpedal connected to a COM-port, a foot pedal connected
to a microHAM keyer can only serve as PTT.

NB. On microHAM keyers, DXLog does not recognize foot pedal 1 and foot pedal 2. Both act as PTT
for the currently focused radio.

Yaesu

For best performance with DXLog your radio needs to have the most recent firmware.
Firmware releases can be found on Yaesu's web site.

FT-817ND, 818, 847, 857D, and 897

Use the highest available speed on the CAT interface (38400bps or 57600bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 300ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

VFO B control is supported by DXLog but due to limitations in the radios' CAT protocol changes in VFO selection or
split status made using the radio's controls will confuse DXLog.

FT-1000 and FT-1000D

Use the highest available speed on the CAT interface. (At 4800bps a suitable polling interval is 500ms.)

Note that the CAT interface uses 2 (TWO) stop bits.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

Subreceiver control is not supported.

The internal voice keyer is not supported.

FT-1000MP and FT-1000MKV

Use the highest available speed on the CAT interface. (At 4800bps a suitable polling interval is 500ms.)

Note that the CAT interface uses 2 (TWO) stop bits.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

Subreceiver control is supported.

The internal voice keyer is not supported.

FT-450D

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 100ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported for both recording and playback.

FTDX1200 and FTDX3000

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 200ms.

For the FTDX3000 the USB CAT interface is strongly recommended.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is supported but only for playback.

FTDX5000

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

With this option enabled, sub receiver control is supported. For more information, see Operating techniques.

The internal voice keyer is supported but only for playback.

FT-991 and FT-991A

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 100ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is not supported.

FTDX101D

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 200ms.

Using the virtual COM port via USB is recommended.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be enabled.

With this option enabled, sub receiver control is supported. For more information, see Operating techniques.

The internal voice keyer is supported both for playback and recording.

Coherent diversity is supported. It can either be enabled/disabled from the keyboard with [Ctrl][-] or [Ctrl][Keypad Subtract] or with a long press
on the radio's SYNC button. Diversity is indicated with a DIV icon right below in the "seven segment" frequency counter in the radio/band map window.

FTDX10

NB. Due to the newness of the radio model and lack of access, DXLog's driver is in an experimental state.

Use the highest available speed on the CAT interface (38400bps, 8 bits, no parity, 2 (TWO) stop bits).
A suitable polling interval is 200ms.

For SO2V operation, Options|Interface specific options|Use SPLIT command in SO2V technique should be disabled.

The internal voice keyer is not supported.