[DXLog.net - Support] CAT PTT via Omnirig

Vassilis Kontothanasis sv1dpj at gmail.com
Fri Apr 24 21:17:44 CEST 2015


Hello,
I know i am off topic but just taking the change to ask if anyone has
somewhere in stock an 1.3 ROM for my FT990, or may indicate a place to
purchase one. I love my old radio and i was not able so far to replace the
old 1.2 Rom in order to control it.

My excuses for my off-topic post

Vasilis SV1DPJ

On Wed, Apr 22, 2015 at 5:46 PM, Neil Powell <neilpowell1 at eircom.net> wrote:

> OK Great Chris,
>
> I have bought the FT1000D home from the shack so will be able to test if
> need be.
>
> Thanks very much as always.
>
> Neil.
>
>   ----- Original Message -----
>   From: 9A5K
>   To: Neil Powell
>   Cc: support at dxlog.net
>   Sent: Wednesday, April 22, 2015 3:18 PM
>   Subject: Re: [DXLog.net - Support] CAT PTT via Omnirig
>
>
>   Thanks Neil.
>
>
>   FT1000D cat is similar to 990 and it's different implementation then old
> one on FT-1000MP..
>
>   I have FT-990 here, so will check it as well.
>
>
>   Same for Omnirig.. more testing later today.
>
>   73,
>
>   Chris - 9A5K
>
>
>
>
>   On Wed, Apr 22, 2015 at 4:08 PM, Neil Powell <neilpowell1 at eircom.net>
> wrote:
>
>     Hi Chris,
>
>     A little information for you, I was in our shack and did some more
> testing with DXLog and setting up the Interlocking as this is a feature we
> would like to use, on the FT5000 connected directly via serial it works
> fine but when using PTT via CAT in Omnirig there is no PTT as before.  On
> an FT1000D the CAT appears to be broken with no CAT communication with the
> radio (4800,8,N,2) even though the Microham MicroKeyer 2 is communicating
> ok (works OK in WinTest) , if I set the rig type to FT990 (which I believe
> is very similar) the frequency works OK but no PTT via CAT, but this might
> be because the command set is different in the 990 I am not sure.  Also
> have an FT920 but this is not a supported Radio with DXLog so tested by
> using Omnirig and again no PTT via CAT with this also.
>
>     The Interlocking concept looks good but obviously with above issues
> have not managed to use it at all yet.
>
>     Thanks
>
>     Neil EI3JE.
>       ----- Original Message -----
>       From: 9A5K
>       To: Neil Powell
>       Cc: support at dxlog.net
>       Sent: Monday, April 13, 2015 10:25 AM
>       Subject: Re: [DXLog.net - Support] CAT PTT via Omnirig
>
>
>       Hi Neil.
>
>
>       Let me check this at dev version.
>
>       If this feature is missing or broken, I will include the fix in next
> release.
>
>       73,
>
>       Chris - 9A5K
>
>
>
>
>       On Mon, Apr 13, 2015 at 11:24 AM, Neil Powell <
> neilpowell1 at eircom.net> wrote:
>
>         Hi Bob,
>
>         I have the lastest version and files for Omnirig installed and
> "pmTx" enable transmit mode and "pmRx" enable receive mode are in the
> config file for the radio but DXLog dosen't seem to be using them.  I am
> hoping it can be sorted as want to use the Footswitch via the comport.
>
>         Neil EI3JE.
>         _______________________________________________
>         Support mailing list
>         Support at dxlog.net
>         http://www.dxlog.net/mailman/listinfo/support
>
>
>
>
> _______________________________________________
> Support mailing list
> Support at dxlog.net
> http://www.dxlog.net/mailman/listinfo/support
>


More information about the Support mailing list