[DXLog.net - Support] An extra DAH when stacking CQ's on other radio

[9A5K]

OK, it is same part of the code.

On Tue, May 10, 2016 at 9:08 AM, Luca NCJ <ik2ncj at gmail.com> wrote:

> Hi Chris
>
> this happens also if you are cq-ing on one radio and press f4 to start the
> call on opposite radio when the cq TX is not over.
> I guess it happens on all cw messages but not tested.
>
> TNX
>
> **** Luca IK2NCJ ****
>
>
>
> 2016-05-10 9:01 GMT+02:00 9A5K <9a5k at 9a5k.com>:
>
>> Hi Ingo.
>>
>> I will check this later today to confirm the issue as well here.
>> If I've got it correctly, it seems that extra letter isn't cleared
>> correctly from the buffer, and it is sent to
>> transceiver.
>>
>> 73,
>> Chris - 9A5K
>>
>>
>> On Mon, May 9, 2016 at 9:30 PM, SM5AJV <sm5ajv at qrq.se> wrote:
>>
>> > Update:
>> >
>> > During the weekends ARI contest I could repeat the problem
>> > and also confirm that the extra "T" actually was sent from DxLog by
>> using
>> > the microHam monitor application for WinKeyer.
>> >
>> > I would like to get this solved and it seems that it is some sort of
>> timing
>> > or interlock issue here? When using Alternating CQ there is no problem,
>> but
>> > there is also a noticeable delay between the two CQ's.
>> >
>> > I also tried to increase the baud rate to WinKey from 1200 bps to 9600,
>> > but the trouble remained.
>> >
>> > As I mentioned earlier, the set-up of messages in the scenario are:
>> > F1: $RESET $TR1 $R1R2 $F1 $R1R2
>> > F6: $RESET $TR2 $R1R2 $F1 $R1R2
>> >
>> >
>> > 73
>> > Ingo SM5AJV
>> >
>> >
>> >
>> >
>> >
>> > 2016-05-01 22:58 GMT+02:00 SM5AJV <sm5ajv at qrq.se>:
>> >
>> > > I have tried both with and without, but didn't notice any difference.
>> > >
>> > > 73
>> > > Ingo SM5AJV / SE5E
>> > > Den 1 maj 2016 22:55 skrev "James Balls" <makidoja at gmail.com>:
>> > >
>> > >> Do you have double buffer set for Winkeyer in DXL?
>> > >> On 1 May 2016 21:27, "SM5AJV" <sm5ajv at qrq.se> wrote:
>> > >>
>> > >> Sorry, I just forgot!
>> > >>
>> > >> I am using a microHam MK2R+ with the latest FW/SW.
>> > >>
>> > >>
>> > >> 73
>> > >> Ingo SM5AJV
>> > >>
>> > >>
>> > >> 2016-05-01 22:02 GMT+02:00 James Balls <makidoja at gmail.com>:
>> > >>
>> > >>> What is your SO2R hardware please ?
>> > >>>
>> > >>> Jim M0CKE
>> > >>> On 1 May 2016 18:25, "SM5AJV" <sm5ajv at qrq.se> wrote:
>> > >>>
>> > >>>> I am playing with SO2R set-up..
>> > >>>>
>> > >>>> Here is some parts of my Scenario set-up:
>> > >>>>
>> > >>>> F1: $RESET $TR1 $R1R2 $F1 $R1R2
>> > >>>> F6: $RESET $TR2 $R1R2 $F1 $R1R2
>> > >>>>
>> > >>>> When I am manually trying to send alternating CQ's an
>> > >>>> extra DAH is sometimes sent on the next CQ:
>> > >>>>
>> > >>>> Push F1 to call CQ on RADIO 1:     TEST SE5E
>> > >>>> directly after the CQ is sent I push F6 to call CQ on RADIO 2: T
>> TEST
>> > >>>> SE5E
>> > >>>>
>> > >>>> This happen if I push the F6 quickly after F1 message is finnished.
>> > >>>> If I wait a while, the extra DAH is not sent.
>> > >>>>
>> > >>>> I have also tried to put in an extra space in the F1 message and
>> then
>> > >>>> the problem disappears. But an extra space will make the CQ too
>> > >>>> sluggish.
>> > >>>>
>> > >>>> Any ideas what's going on?
>> > >>>>
>> > >>>>
>> > >>>> 73
>> > >>>> Ingo SM5AJV / SE5E
>> > >>>> _______________________________________________
>> > >>>> Support mailing list
>> > >>>> Support at dxlog.net
>> > >>>> http://www.dxlog.net/mailman/listinfo/support
>> > >>>>
>> > >>>
>> > >>
>> > _______________________________________________
>> > Support mailing list
>> > Support at dxlog.net
>> > http://www.dxlog.net/mailman/listinfo/support
>> >
>> _______________________________________________
>> Support mailing list
>> Support at dxlog.net
>> http://www.dxlog.net/mailman/listinfo/support
>>
>
>