[DXLog.net - Support] An extra DAH when stacking CQ's on other radio

[Luca NCJ]

Hi Chris

this happens also if you are cq-ing on one radio and press f4 to start the
call on opposite radio when the cq TX is not over.
I guess it happens on all cw messages but not tested.

TNX

**** Luca IK2NCJ ****



2016-05-10 9:01 GMT+02:00 9A5K <9a5k at 9a5k.com>:

> Hi Ingo.
>
> I will check this later today to confirm the issue as well here.
> If I've got it correctly, it seems that extra letter isn't cleared
> correctly from the buffer, and it is sent to
> transceiver.
>
> 73,
> Chris - 9A5K
>
>
> On Mon, May 9, 2016 at 9:30 PM, SM5AJV <sm5ajv at qrq.se> wrote:
>
> > Update:
> >
> > During the weekends ARI contest I could repeat the problem
> > and also confirm that the extra "T" actually was sent from DxLog by using
> > the microHam monitor application for WinKeyer.
> >
> > I would like to get this solved and it seems that it is some sort of
> timing
> > or interlock issue here? When using Alternating CQ there is no problem,
> but
> > there is also a noticeable delay between the two CQ's.
> >
> > I also tried to increase the baud rate to WinKey from 1200 bps to 9600,
> > but the trouble remained.
> >
> > As I mentioned earlier, the set-up of messages in the scenario are:
> > F1: $RESET $TR1 $R1R2 $F1 $R1R2
> > F6: $RESET $TR2 $R1R2 $F1 $R1R2
> >
> >
> > 73
> > Ingo SM5AJV
> >
> >
> >
> >
> >
> > 2016-05-01 22:58 GMT+02:00 SM5AJV <sm5ajv at qrq.se>:
> >
> > > I have tried both with and without, but didn't notice any difference.
> > >
> > > 73
> > > Ingo SM5AJV / SE5E
> > > Den 1 maj 2016 22:55 skrev "James Balls" <makidoja at gmail.com>:
> > >
> > >> Do you have double buffer set for Winkeyer in DXL?
> > >> On 1 May 2016 21:27, "SM5AJV" <sm5ajv at qrq.se> wrote:
> > >>
> > >> Sorry, I just forgot!
> > >>
> > >> I am using a microHam MK2R+ with the latest FW/SW.
> > >>
> > >>
> > >> 73
> > >> Ingo SM5AJV
> > >>
> > >>
> > >> 2016-05-01 22:02 GMT+02:00 James Balls <makidoja at gmail.com>:
> > >>
> > >>> What is your SO2R hardware please ?
> > >>>
> > >>> Jim M0CKE
> > >>> On 1 May 2016 18:25, "SM5AJV" <sm5ajv at qrq.se> wrote:
> > >>>
> > >>>> I am playing with SO2R set-up..
> > >>>>
> > >>>> Here is some parts of my Scenario set-up:
> > >>>>
> > >>>> F1: $RESET $TR1 $R1R2 $F1 $R1R2
> > >>>> F6: $RESET $TR2 $R1R2 $F1 $R1R2
> > >>>>
> > >>>> When I am manually trying to send alternating CQ's an
> > >>>> extra DAH is sometimes sent on the next CQ:
> > >>>>
> > >>>> Push F1 to call CQ on RADIO 1:     TEST SE5E
> > >>>> directly after the CQ is sent I push F6 to call CQ on RADIO 2: T
> TEST
> > >>>> SE5E
> > >>>>
> > >>>> This happen if I push the F6 quickly after F1 message is finnished.
> > >>>> If I wait a while, the extra DAH is not sent.
> > >>>>
> > >>>> I have also tried to put in an extra space in the F1 message and
> then
> > >>>> the problem disappears. But an extra space will make the CQ too
> > >>>> sluggish.
> > >>>>
> > >>>> Any ideas what's going on?
> > >>>>
> > >>>>
> > >>>> 73
> > >>>> Ingo SM5AJV / SE5E
> > >>>> _______________________________________________
> > >>>> Support mailing list
> > >>>> Support at dxlog.net
> > >>>> http://www.dxlog.net/mailman/listinfo/support
> > >>>>
> > >>>
> > >>
> > _______________________________________________
> > Support mailing list
> > Support at dxlog.net
> > http://www.dxlog.net/mailman/listinfo/support
> >
> _______________________________________________
> Support mailing list
> Support at dxlog.net
> http://www.dxlog.net/mailman/listinfo/support
>