[DXLog.net - Support] Observations Using the DXLOG at the CQWWRTTY

Hector Garcia XE2K j_hector_garcia at sbcglobal.net
Mon Sep 30 06:02:35 CEST 2013


Thanks for the fast response
Let me complement  some points, 

the zone was pre filled,   most countries and US calls show  a zone, most DXCC show his correct zone
not the most  Russian , US was almost all 05
the JA's those  show as 25
tks for the advise in the double click  next time

I was working 2Tone main , MMVARI secundary 
MMVARI always work , I do not install  or have MMTTY at the moment working  with DXLOG
yes on Writelog and stand alone

Difference in the freq from the bandmap and Status now is fixed 
Thank you for the tip

Yes I was using the List in the bandmap, was the best option

RUN SP typed and working fine,  now I will make it my RTTY and CW daily use F keys with that
thanks,  If I look that do not read the manual  or the Help , yes I didn't  I'm lost

Again thank you Bob


J.Hector Garcia  XE2K / AD6D
Mexicali B.C  DM22fp / El Centro
P.O.Box 73 
El Centro CA 92244-0073
Tweeter @XE2K

 From: "Bob Wilson, N6TV" <n6tv at arrl.net>
To: DXLog.net Reflector <support at dxlog.net> 
Sent: Sunday, September 29, 2013 8:24 PM
Subject: Re: [DXLog.net - Support] Observations Using the DXLOG at the CQWWRTTY

On Sun, Sep 29, 2013 at 7:11 PM, Hector Garcia XE2K <
j_hector_garcia at sbcglobal.net> wrote:

> the module only allow capture  the ZONE number  but there is no space  for
>  the STATE or PROVINCE during the CLICK in the screen
> need to be used the space bar and write the state next to the zone, making
> that manual

I couldn't figure out how DXLog.net was pre-filling the Zone.  It didn't
seem like it was looking it up in cty_wt_mod.dat properly.  Some JA
stations were not even listed in zone 25?

> the ESC do not cancel  the F keys message when you  press 2 or more times
> or 2 keys one after the other , you need to wait to pass all the
> message

Right, Escape it stops the message, but it doesn't clear the buffer like
you expect it to.

> ERROR message
> WndTXProc.CPP waveoutWrite  error line154

I think that must be part of 2Tone not DXLog.net.

> TXfsk switch case 0:error  clic cancel
> and later again the same error window
> this error made that the 2tone rx window show all received text is blue
> like the transmitted message , after  one more tx from me the
> color in RX back to black and blue for TX

I used MMTTY for transmitting FSK, 2Tone and MMTTY for receive windows.  I
couldn't get MMVARI to work inside DXLog.net, even though it works OK

> The freq reading in the  VFO A in the bandmap and also the logged  is
> different

Yes, try Options -> Interface specific options -> Use decoder freq
correction (uncheck this option and frequency display should be fixed).

REQUEST  if is possible  for later updates
> Will like to be included this options:
> --Check partials do not allow to select with  the mouse (click) the call
> and get inserted in the  entry area.

This seems to work already (was new in 2.0.12), but you have to
double-click on the call in the check partial window, not single click.

--Will like to be able to get access to the F keys (keyboard) clicking any
> screen from the LOG (Digital, check partials, status, etc Not only the main
>  log window)

Maybe you are using Options -> Windows -> Floating?  Try using the other
option; all the Function keys seem to work OK when any DXLog.net window has
the focus.

But it would be nice for DXLog.net to automatically grab the focus every 5
or 10 seconds like N1MM does.

> -- Be able to expand or contract the BANDMAP to see more a detail the freq
>  where was the QSO  I will like to see 30-40 khz at most

First, consider using the LIST tab in the bandmap, to see all spots.

Second, you can press Alt+Scroll wheel up/down while the mouse is over the
window and it will expand or contract.  Funny bug, Ctrl+mouse wheel
up/down, both directions make the window smaller! :-)

--- Get an easy access key or where to click to select standar  and S&P
> message

Ctrl+Tab swaps Run and S&P modes and messages (status shown in clock
window), but first type RUNSP [Enter] in the logging window to enable
RUN/S&P switching.

Bob, N6TV
Support mailing list
Support at dxlog.net

More information about the Support mailing list